OEM style '70-'71 E-body 2 piece proportioning/metering valve
Adapt common, inexpensive '73 and newer 10.95" A,B,E,F,M,J Body rotors to original '70-'72 B/E body disc brake knuckles
Reproduction '71-'74 Mopar B/E body manual brake firewall stiffening plate
Pair, NEW '73-'89 Mopar front SLIDER type calipers are assembled with brake pads and clips.
BLACK powder-coated front calipers fit '73 and newer SLIDER type caliper brackets found on many Mopar A,B,E,F,M,J and R bodies equipped with original or OEM type Mopar front disc brake conversions.
These calipers DO NOT fit PIN type caliper brackets.
These calipers DO NOT fit any full-size Mopar C body, truck or van.
Pair, NEW '94-'04 Mustang COBRA rear calipers are assembled with brake pads and clips.
RED powder-coated rear calipers only fit '94-'04 Mustang COBRA/BULLIT/MACH1 with VENTED rear rotors. These calipers DO NOT fit any other Mustang model with SOLID rear rotors.
Use a distribution block for four wheel drum or four wheel disc applications.
Reproduction '73-'74 A-body proportioning valve
Reproduction 10.95" caliper brackets accept all commonly available '70s-'80s midsize Mopar (slider type) calipers, bearings and hoses.
Upgrade stock 10.95" diameter disc brakes to 11.75" Cordoba rotors.
Super-Duty heim joint style adjustable push rod fits all Mopar A-bodies and '62-'70 B-bodies equipped with manual brakes
Adjustable proportioning valve is used to reduce brake line pressure.
Package includes new, aluminum master cylinder with large rectangular reservoir, billet aluminum 4 hole or 4 stud adapter and push rod retaining ring.
Reproduction Bendix dual diaphragm brake booster provides maximum assist for high performance applications
Reproduction E-body metering brake valve fits '70-'71 Barracuda and Challengers equipped with front disc and rear drum brakes.
Mopar A, B, and E Body front brake line selector allows you to pick hard lines and flex hoses for your car, master cylinder, and disc or drum combination.
conversion caliper brackets fit '62-72 B and E body Mopar DRUM knuckles
Mopar A, B, and E Body front to rear brake line selector allows you to pick hard lines and proportioning/brake valves for your car and disc or drum combination.
Install a late model aluminum Mopar 2-bolt master cylinder in place of your original 4-hole or 4-stud iron master cylinder with this billet aluminum adapter.
Zinc plated vent bolt retains the brake tee located on most Mopar rear wheel drive vehicles
A-body offset adapter increases clearance between the master cylinder and valve cover
Mopar A, B, and E Body rear axle brake line selector allows you to pick hard lines, flex hoses, brass tee, and vent bolt for your disc or drum combination.
Mopar drum brake assembly includes powder-coated backing plates, new wheel cylinders, new hardware and new drums installed.
Handy kit includes the necessary components to rebuild 10 x 2 1/2" or 11 x 2 1/2" Mopar rear drum brakes
Reproduction forged steel disc brake knuckles fit '62-'72 B-bodies, '70-'74 E-bodies and '67-'76 A-bodies.
Reproduction splash shields fit '73 and newer A,B,E,F,M,J and R body disc brake knuckles.
Drilled/slotted/plated 11.75" or 10.95" rotors fit '73 and newer OEM and Reproduction Mopar A/B/E/F/M/J/R Body knuckles. For use with pin or slider type calipers.
DOT stainless front brake flex hose kit with 9/16" banjo bolts, crush-washers and hose clips. Available in 15" or 18" for front or rear mount calipers.
Mopar Stainless Steel Rear Brake Hose w/Tee
Fit '2002 and earlier (first generation) Viper front calipers and 11.75" x 1.25" rotors on Mopar '62-'72 B-bodies and '70-'72 E-bodies equipped with stock DRUM knuckles
© 2007-2020 DoctorDiff. We speak Mopar.