.
Reproduction 8 3/4" clutch sure-grip ("powr-lok") includes upgraded 1 piece 30 spline side gears and 4340 cr-mo spider gears
Mopar Tapered Axle Bearing Package
Ten press-in wheel lug studs for Mopar 8 3/4" axle shafts.
8 3/4" ring and pinions for 741, 742, or 489 cases. Various ratios.
30 or 35 spline, 5 X 4 1/2" bolt pattern axle package for 8 3/4" or Dana 60 with lug studs and Green sealed wheel bearings INSTALLED.
Professional tool removes ALL popular carrier bearings quickly and easily with no damage to the bearing.
Choose ring gear bolts for Mopar 8 3/4" or Dana 60
Choose pinion nut and washer for Dana 60, Mopar 9 1/4", or Mopar 8 3/4" pinions.
New, super duty Mopar shock plates fit any '64-'76 A-Body, '62-72 B-Body, '64-'72 C-Body and '70-'74 E-Body equipped with standard 3" axle tubes. Will not fit 7.25" rearends.
Package includes (10) 3/8"-24 x 1 1/4" housing studs and nuts used to secure Mopar 8 3/4" and For 9" third-members to their housings.
Ford Motorcraft limited slip additive is recommended for Mopar 8.75" and Dana 60 clutch or cone style sure-grips. 1 bottle controls clutch sticking and chatter.
OEM Mopar 3/8"-24 x 1 1/4" housing end studs and nuts used to secure Mopar 8 3/4" and passenger car Dana 60 brake backing plates and wheel bearings.
Package fits aftermarket axles tapped for 1/2" screw-in studs. Use with disc brakes and thick wheels for NHRA drag racing requirements.
Powder-coated OEM Mopar passenger car 8.75" pinion snubber (various years).
8.75" Eaton True-Trac fits all 8.75" castings all ratios and all stock axles.
"Powr-Lok" clutch pack includes the plates and discs necessary to rebuild a Mopar 8 3/4" or Dana 60 clutch-type differential.
New, nodular iron 489 casting built with forged steel caps, billet adjusters, crush sleeve eliminator and choice of ratio, yoke, clutch sure-grip or spool.
New, Mopar 8 3/4" nodular iron 489 casting includes forged steel caps and billet steel adjusters.
Handy kit includes the small parts required to perform a Mopar 8 3/4" gear swap.
Your choice of quality Koyo carrier bearings for either late or early model 8 3/4" third members.
8 3/4" billet steel housing ends fits Mopar spec brakes and MO-400/ST-400 snap-ring style Green wheel bearings
Premium quality Mopar 8 3/4" third member gasket.
Zinc plated vent bolt retains the brake tee located on most Mopar rear wheel drive vehicles
Spring perches fit GM 12 bolt, Mopar 8 3/4", Dana 60, Ford 9" and other rearends.
Premium quality Mopar 8.75" pinion seal. Choose 742 or 741/489 case
For Dana 60, Dana 44 or Mopar 8 3/4. BRAND NEW PARTS FIT HEAVY DUTY, 4 SPIDER GEAR TYPE ("POWR-LOK") SUREGRIP UNITS
8 3/4" Spanner Wrench carrier bearing side adjuster wrench
Lightweight 30 and 35 spline spool fits all 8 3/4" castings and all ratios.
Mopar 8 3/4" 489 Case Crush Sleeve Elminator
Mopar 8 3/4" 489, 741, or 742 case bearing rebuild kit
Mopar A-Body 8 3/4" Housing & Axle Package
Includes gaskets, and seals
Mopar Green Bearings for 8 3/4" and Dana 60 rearends