P
"Powr-Lok" clutch pack includes all steel plates necessary to rebuild a Mopar 8 3/4" or Dana 60 clutch-type differential.
For Dana 60, Dana 44 or Mopar 8 3/4. BRAND NEW PARTS FIT HEAVY DUTY, 4 SPIDER GEAR TYPE ("POWR-LOK") SUREGRIP UNITS
Ten press-in wheel lug studs for Mopar 8 3/4" axle shafts.
Your choice of quality Koyo carrier bearings for either late or early model 8 3/4" third members.
Mopar 8 3/4" 489 Case Crush Sleeve Elminator
New, nodular iron 489 casting built with forged steel caps, billet adjusters, crush sleeve eliminator and choice of ratio, yoke, clutch sure-grip or spool.
Mopar 8 3/4" 489, 741, or 742 case bearing rebuild kit
Reproduction 8 3/4" clutch sure-grip ("powr-lok") includes upgraded 1 piece 30 spline side gears and 4340 cr-mo spider gears
8.75" Eaton True-Trac fits all 8.75" castings all ratios and all stock axles.
Lightweight 30 and 35 spline spool fits all 8 3/4" castings and all ratios.
Handy kit includes the small parts required to perform a Mopar 8 3/4" gear swap.
New, Mopar 8 3/4" nodular iron 489 casting includes forged steel caps and billet steel adjusters.
Premium quality Mopar 8.75" pinion seal. Choose 742 or 741/489 case
Powder-coated OEM Mopar passenger car 8.75" pinion snubber (various years).
8 3/4" ring and pinions for 741, 742, or 489 cases. Various ratios.
8 3/4" Spanner Wrench carrier bearing side adjuster wrench
Premium quality Mopar 8 3/4" third member gasket.
Mopar A-Body 8 3/4" Housing & Axle Package
30 or 35 spline, 5 X 4 1/2" bolt pattern axle package for 8 3/4" or Dana 60 with lug studs and Green sealed wheel bearings INSTALLED.
8 3/4" billet steel housing ends fits Mopar spec brakes and MO-400/ST-400 snap-ring style Green wheel bearings
Professional tool removes ALL popular carrier bearings quickly and easily with no damage to the bearing.
Ford Motorcraft limited slip additive is recommended for Mopar 8.75" and Dana 60 clutch or cone style sure-grips. 1 bottle controls clutch sticking and chatter.
Mopar Green Bearings for 8 3/4" and Dana 60 rearends
Includes gaskets, and seals
Spring perches fit GM 12 bolt, Mopar 8 3/4", Dana 60, Ford 9" and other rearends.
OEM Mopar 3/8"-24 x 1 1/4" housing end studs and nuts used to secure Mopar 8 3/4" and passenger car Dana 60 brake backing plates and wheel bearings.
Zinc plated vent bolt retains the brake tee located on most Mopar rear wheel drive vehicles
Choose pinion nut and washer for Dana 60, Mopar 9 1/4", or Mopar 8 3/4" pinions.
Choose ring gear bolts for Mopar 8 3/4" or Dana 60
Package fits aftermarket axles tapped for 1/2" screw-in studs. Use with disc brakes and thick wheels for NHRA drag racing requirements.
New, super duty Mopar shock plates fit any '64-'76 A-Body, '62-72 B-Body, '64-'72 C-Body and '70-'74 E-Body equipped with standard 3" axle tubes. Will not fit 7.25" rearends.
Mopar Tapered Axle Bearing Package
Package includes (10) 3/8"-24 x 1 1/4" housing studs and nuts used to secure Mopar 8 3/4" and For 9" third-members to their housings.
